{{recommendedBannerText}}

Spacer
{{recommendedRegLangFull}}

Wastewater Aeration, Controls & Energy Management

What is Wastewater Aeration?

Wastewater aeration is critical to biological wastewater treatment systems including aerobic activated sludge systems, Sequencing Batch Reactors (SBR), nitrification-denitrification in a single basin, and Membrane Bioreactors (MBR).

These treatment systems inject pressurized air into a liquor of sludge and wastewater, promoting the growth of microorganisms that consume organic matter and supply the air for diffused aeration systems.

Are you interested in learning more about what our products can do for your wastewater aeration process? Then click the cards below to review our extensive portfolio.

Wastewater Aeration Offering

What is Wastewater Aeration? 

Wastewater aeration is part of the secondary or activated sludge treatment process in municipal and industrial wastewater treatment.

Aeration is an activated sludge process. Activated sludge is a process with a high concentration of microorganisms. Bacteria that are present are kept in suspension by stirring. The intent is to remove this organic matter and bacteria from the wastewater. 

In this phase, biological processes, like aerobic treatment, decompose organic compounds, and pollutants in the wastewater. Chemical oxidation is a process that is used to remove persistent organic pollutants, bacteria, and microbial pathogens. 

What is the Result of Wastewater Aeration? 

Typically, the secondary phase removes chemicals and toxic compounds. It is not uncommon to repeat this phase several times or apply tertiary treatment to the water. 

Why is Wastewater Aeration Important? 

Aeration is critical to wastewater treatment. A well-designed aeration system directly impacts the level of wastewater treatment it achieves. The key to rapid, economic, safe, and effective wastewater treatment is an aeration system that evenly distributes oxygen supply. 

How is Wastewater Aerated?

Aeration is an activated sludge process. It pumps air into a tank, promoting microbial growth in wastewater. Bacteria that forms the activated sludge, after settling in a separate settling tank, recirculates back to the aeration basin. Recirculating back to the aeration basin increases the decomposition rate.

 

Wastewater Aeration Plant Design

Plant design and wastewater treatment methods used can vary greatly. High volumes of wastewater will require larger and more complex systems than the simple batch processes used by smaller-scale treatment facilities. The wastewater aeration plant design shows how a system impacts the level of wastewater treatment achieved.

Wastewater Aeration Plant Layout

Wastewater Treatment Aeration Locations

The wastewater aeration phase removes organic matter, fine particles, and potentially toxic and harmful chemicals from the influent that enters the system. Read on to more about wastewater treatment aeration locations. 

Aeration Basins & Aerobic Digesters 

An aerated lagoon or aerated basin is a holding treatment pond that supplies artificial aeration. Artificial aeration promotes the biological oxidation of wastewater. These aeration basins use oxygen (or air) and microbial action to biotreat the pollutants in wastewater.

Aerobic digesters and aeration basins are very similar. Aeration basins are large, open earthen lagoons or ponds. The large surface areas involved cause more drastic temperature variations than found in aerobic digesters. Thus, causing variations in sludge retention times. If solids return to the aeration basin process, then there is no difference between an aeration basin and the activated sludge process.

Aerobic digesters are tanks constructed of concrete and are rectangular so multiple tanks can share common walls. Large tanks would have fewer diffusers where most plants have at least two digesters. The aerobic digestion process can be continuous or batch.

Aeration in Wastewater Treatment

Suspension Mixed Lagoons

Suspension mixed lagoons convert the soluble, biodegradable organics in the influent into biomass that can settle as sludge. Usually, the effluent goes to a second pond where the sludge can settle. Then, it is removed from the top with a low chemical oxygen demand (COD), while the sludge accumulates on the floor and undergoes anaerobic stabilization.

Floating Surface Aerators 

In a surface aerated system, the aerators provide two functions.

(1) They transfer air into the basins to facilitate biological oxidation reactions.

(2) They provide the mixing required for dispersing the air and for contacting the reactants (that is, oxygen, wastewater, and microbes).

Typically, the floating surface aerators deliver sufficient oxygen or air for aeration. However, surface aerators do not provide mixing equivalent to the mixing that normally is achieved in activated sludge systems.

Biological oxidation processes are sensitive to temperatures between 32°F and 104°F (0°C and 40°C). The rate of bio-reactions increases with temperature. Most surface aerated vessels operate between 39°F and 90°F (4°C and 32°C).

Submerged Diffused Aeration

Submerged diffused air is essentially a form of a diffuser grid inside a lagoon. The two main types of submerged diffused aeration systems for lagoon applications are floating lateral and submerged lateral. Both systems utilize fine or medium bubble diffusers to provide aeration and mixing of the process water. The diffusers can be suspended slightly above the lagoon floor or may rest on the bottom.

Channel Aeration 

Channels that distribute wastewater to the primary sedimentation tanks are aerated to keep the solids in suspension, and independent of the water flow rate. The amount of air required ranges from 2-5 cfm per linear foot of the channel (0.2-0.5 m3/linear meter/minute). The mixed liquor turns to activated sludge settling tanks that are aerated.

Post Aeration 

Recent requirements for effluent demand high dissolved oxygen levels (4 to 8 MG/L). The regulation intends to ensure that low dissolved oxygen level effluent does not mix with a receiving stream.

One method is cascade aeration, where the effluent is aerated by the turbulence of a series of waterfalls. However, the temperature of the water greatly affects the water’s ability to absorb oxygen.  

In larger treatment plants, non-porous (coarse bubble) and porous (fine bubble), diffuser aeration is used.  The choice of a diffuser is dependent on the oxygen transfer rate required by the effluent.


HOFFMAN & LAMSON Blower for Wastewater Aeration Processes
Post Aeration

Center of Excellence for Wastewater Solutions

The Hoffman & Lamson brand heritage brings over 25 years of innovation and experience to water and wastewater treatment solutions. Whether you are treating water for clean water supply or treating wastewater, Hoffman & Lamson offers the most comprehensive range of blowers/exhausters and engineered packaged solutions of any manufacturer, marking us a true center of excellence for wastewater solutions.

en-PH